Suomi
English
Latviešu
Русский
Lietuvos
Eesti
Tachograph emulator for Peugeot Boxer (2007->), Fiat, Citroen. TACHOEMU
SKU: 13826
Fiat Ducato (2007->), Peugeot Boxer (2007->), Citroen Jumper (2007->), Relay (2007->) takografin emulaattori.
Attention !
When placing an order, please pay attention to the line: "For immediate delivery:" The delivery time for out-of-stock items may take from 1 to 30 days.
For customers from non-EU countries, the cost of goods is automatically reduced by 21% (LV VAT).
For EU companies (with legal VAT), the cost of goods is automatically reduced by 21% (LV VAT).
Worldwide shipping, cost calculated at checkout.
Some items in our store on www.ebay.com
When placing an order, please pay attention to the line: "For immediate delivery:" The delivery time for out-of-stock items may take from 1 to 30 days.
For customers from non-EU countries, the cost of goods is automatically reduced by 21% (LV VAT).
For EU companies (with legal VAT), the cost of goods is automatically reduced by 21% (LV VAT).
Worldwide shipping, cost calculated at checkout.
Some items in our store on www.ebay.com
Saatavilla nyt:
4 varastossa
+ Saatavilla 8–9 päivässä
99
€89.00
Fiat, Peugeot, Citroen tachograph emulator.
TACHOEMU
Many Citroen, Fiat and Peugeot light commercial vehicles are fitted with digital tachograph (usually digital Actia smartach) .
On some vehicles, converted for personal use, the Tachograph is an unneccessary annoyance.
Unfortunately, simply removing the Tachograph is not possible because the Tachograph also produces a speed signal for the Engine ECU and speedometer.
With TACHOEMU you can easy solve this problem.
The TACHOEMU allows the removal of the factory Tachograph from Citroen, Fiat and Peugeot vehicles while retaining the normal operation of the speedometer.
- Fiat Ducato (2007->),
- Peugeot Boxer (2007->),
- Citroen Jumper (2007->), Relay (2007->)...
This tachograph emulator can convert tachograph speed sensor signal to digital signal for instrument cluster speedometer.
How to install:
- remove tachograph from car and disconnect all connectors from it;
- on A connector find pin A5 (-Batt), connect it (short wires) with connector B2 (Sensor-) wire and with TACHOEMU pin GND;
- on A connector find pin A3 (+Ignition 15), connect it (short wires) with connector B1 (Sensor+) wire and with TACHOEMU pin +12V;
- wire from pin B3(Speed Signal) connect with TACHOEMU pin out;
- wire from pin B7(Speed Out) connect with TACHOEMU pin in.
If speedometer show incorrect speed after TACHOEMU instalation:
You can change K-factor (speed impulse / kilometer) .
Connect TACHOEMU to car and make driving test. If vehicle speed not correspond speedometer - change K-factor.
Default programmed TACHOEMU K-factor is 5100 imp/km.
You can change K-factor by connecting TACHOEMU K-line pin to GND for 2 seconds on working emulator.
K-factor will change to the next position from list:
5100 imp/km, 5300, 5500, 6000, 4000, 4500, 4800 - after K-factor change test vehicle speedometer again.
Product: www.codecard.lt
| Brändi | Codecard |
|---|---|
| Automerkin mukaan | Peugeot |
| CAN bus, K line... filters, emulators | CAN filters, emulators other |
| Tilavuuspaino | 100g |
0.0
yhteensä
(0 asiakasarvostelua)
Arvosteluja ei ole vielä.